在Centos 5.6下安装 dynamips
作者 佚名技术
来源 Linux系统
浏览
发布时间 2012-04-03
| 0/0 interface? [yes]: y Use the 100 Base-TX (RJ-45) connector? [yes]: y Operate in full-duplex mode? [no]: y Configure IP on this interface? [yes]: 216.16.16.77 % Please answer ''yes'' or ''no''. Configure IP on this interface? [yes]: y IP address for this interface: 216.16.16.77 Subnet mask for this interface [255.255.255.0] : 255.255.255.0 Class C network is 216.16.16.0, 24 subnet bits; mask is /24 Do you want to configure Serial1/0 interface? [yes]: y Configure IP on this interface? [yes]: y Configure IP unnumbered on this interface? [no]: n IP address for this interface: 172.16.0.5 Subnet mask for this interface [255.255.0.0] : 255.255.255.252 Class B network is 172.16.0.0, 30 subnet bits; mask is /30 Do you want to configure Serial1/1 interface? [yes]: n Do you want to configure Serial1/2 interface? [yes]: n Do you want to configure Serial1/3 interface? [yes]: n The following configuration command script was created: hostname croutera3640 enable secret 5 $1$23Hu$R4Fvrz7dFHw.sJesE4kww. enable password aaa1 line vty 0 4 password aaa2 no snmp-server ! ip routing no bridge 1 ! interface FastEthernet0/0 media-type 100BaseX full-duplex ip address 216.16.16.77 255.255.255.0 ! interface Serial1/0 ip address 172.16.0.5 255.255.255.252 ! interface Serial1/1 shutdown no ip address ! interface Serial1/2 shutdown no ip address ! interface Serial1/3 shutdown no ip address dialer-list 1 protocol ip permit dialer-list 1 protocol ipx permit ! end [0] Go to the IOS command prompt without saving this config. [1] Return back to the setup without saving this config. [2] Save this configuration to nvram and exit. Enter your selection [2]: 2 media-type 100BaseX ^ % Invalid input detected at ''^'' marker. Building configuration... Use the enabled mode ''configure'' command to modify this configuration. Press RETURN to get started! *Mar 1 00:00:03.767: %LINK-3-UPDOWN: Interface FastEthernet0/0, changed sta *Mar 1 00:00:03.771: %LINK-3-UPDOWN: Interface Serial1/0, changed state to *Mar 1 00:00:03.775: %LINK-3-UPDOWN: Interface Serial1/1, changed state to *Mar 1 00:00:03.779: %LINK-3-UPDOWN: Interface Serial1/2, changed state to *Mar 1 00:00:03.783: %LINK-3-UPDOWN: Interface Serial1/3, changed state to *Mar 1 00:00:04.767: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEt *Mar 1 00:00:04.771: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial *Mar 1 00:00:04.775: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial *Mar 1 00:00:04.779: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial *Mar 1 00:00:04.783: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial *Mar 1 00:00:32.399: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial *Mar 1 00:00:32.471: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial *Mar 1 00:00:32.535: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial *Mar 1 00:00:32.615: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial * |
凌众科技专业提供服务器租用、服务器托管、企业邮局、虚拟主机等服务，公司网站：http://www.lingzhong.cn 为了给广大客户了解更多的技术信息，本技术文章收集来源于网络,凌众科技尊重文章作者的版权，如果有涉及你的版权有必要删除你的文章，请和我们联系。以上信息与文章正文是不可分割的一部分,如果您要转载本文章,请保留以上信息，谢谢! |
你可能对下面的文章感兴趣
上一篇: 如何架设Linux打印服务器下一篇: linux系统账号和密码策略
关于在Centos 5.6下安装 dynamips的所有评论
