Cisco6000MSFC口令的恢复
作者 佚名技术
来源 网络技术
浏览
发布时间 2012-07-01
| Contents Description Step-by-Step Procedure Example of a Password Recovery on the Catalyst 6000 MSFC Module Related Information Description This document describes the password recovery procedure for the Cisco Catalyst 6000 Multilayer Switch Feature Card (MSFC). Step-by-Step Procedure Attach a terminal or PC with terminal emulation to the console port of the switch. Use the following terminal settings: 9600 baud, no parity, 8 data bits, 1 stop bit Type show module to determine the MSFC card on which to do password recovery. The MSFC module is in slot 15 or 16. Reset the MSFC module you want to do password recovery on. Use the reset Wait 5 seconds and then connect to the MSFC console using the switch console command. After seeing the message "Connected to Router", issue a break sequence. The break key is a unique sequence that will break the MSFC into rommon. If this does not work, please refer to the break sequence page. The MSFC will boot to a rommon> prompt. Type confreg 0x42 at the rommon> prompt to configure the MSFC to boot without its configuration. Display the current software in bootflash by issuing the dir bootflash: command and record the current software version. Boot the system with the boot bootflash: command. NOTE : Do NOT boot the system using the c6msfc-boot image. Doing so will result in loss of configuration after the password recovery process. After the system boots, answer "No" to all the set-up questions or press Ctrl-C to skip the initial set-up procedure. Type enable at the Router> prompt. This will put you in enable mode and you will see the Router# prompt. Type config mem or copy startup-config running-config to copy the nonvolatile RAM (NVRAM) into memory. This is a crucial step. DO NOT save the configuration (do not use write term or copy running-config startup-config) Type write terminal or show running-config. At this point, you should see the full configuration with the unknown enable password or enable secret. All other interfaces are shut down. Type configure terminal to make the necessary changes. The prompt is now hostname(config)# Type enable secret Use the no shutdown command on interfaces that are being used. If you use the show ip interface brief command, every interface that you want to use should be up. Type config-register 0x2102 Press Ctrl-Z to leave the configuration mode. The prompt is now hostname# Type write memory or copy running-config startup-confi g to commit the changes. Example of a Password Recovery on the Catalyst 6000 MSFC Module switch (enable) show module Mod Slot Ports Module-Type Model Status --- ---- ----- ------------------------- ------------------- -------- 1 12 1000BaseX Supervisor WS-X6K-SUP1A-2GEok 15 11 Multilayer Switch Feature WS-F6K-MSFC ok 3 34810/100BaseTX Ethernet WS-X6248-RJ-45 ok 4 48 1000BaseX EthernetWS-X6408-GBIC ok 5 52 MM OC-12 ATM WS-X6101-OC12-MMF ok Mod Module-Name Serial-Num --- ------------------- ----------- 1 SAD03423133 15 SAD0 |
凌众科技专业提供服务器租用、服务器托管、企业邮局、虚拟主机等服务，公司网站：http://www.lingzhong.cn 为了给广大客户了解更多的技术信息，本技术文章收集来源于网络,凌众科技尊重文章作者的版权，如果有涉及你的版权有必要删除你的文章，请和我们联系。以上信息与文章正文是不可分割的一部分,如果您要转载本文章,请保留以上信息，谢谢! |
你可能对下面的文章感兴趣
上一篇: Cisco路由器的口令恢复技巧下一篇: Cisco系列路由器密码恢复研究与实践
关于Cisco6000MSFC口令的恢复的所有评论
