Cisco交换机设置点滴(一)
| ot-trunking
5/12 auto not-trunking Port Vlans allowed ------- --------------------------------------------------------------------- 1/1 1-1000 1/2 1-1000 2/1-2 1-1000 5/1 1-1000 5/2 1-1000 5/3 1-1000 5/4 1-1000 5/5 1-1000 5/6 1-1000 5/7 1-1000 5/8 1-1000 5/9 1-1000 5/10 1-1000 5/11 1-1000 5/12 1-1000 Port Vlans active ------- --------------------------------------------------------------------- 1/1 1 1/2 1 2/1-2 1 5/1 1 5/2 1 5/3 1 5/4 1 5/5 1 5/6 1 5/7 1 5/8 1 5/9 1 5/10 1 5/11 1 5/12 1 注意: DISL在Cisco IOS软件中不支持. 分配VLAN到端口 Cat5001> (enable) set vlan 2 3/2-20 VLAN 2 modified. VLAN 1 modified. VLAN Mod/Ports ---- ----------------------- 2 1/1 3/2-20 Cat5001> (enable) set vlan 20 5/1-6 VLAN 20 modified. VLAN 1 modified. VLAN Mod/Ports ---- ----------------------- 20 1/1 5/1-6 Configure additional information for VLAN 20. On the other Catalyst 5000 : Cat5002> (enable) set vlan 2 4/1-2,5/6-12 VLAN 2 modified. VLAN 1 modified. VLAN Mod/Ports ---- ----------------------- 2 1/2 4/1-3,4/5-23 5/6-12 Configure additional information for VLAN 20. Cat5002> (enable) set vlan 20 5/1-5 VLAN 20 modified. VLAN 1 modified. VLAN Mod/Ports ---- ----------------------- 20 1/2 5/1-5 Configure VLAN 20 on a VTP server. 显示端口配置 Cat5001> (enable) show port Port Name Status Vlan Level Duplex Speed Type 1/1 connected 1 normal half 100 100BaseTX 1/2 connected trunk normal half 100 100BaseTX 2/1 connecting 1 normal half 100 FDDI 2/2 connected 1 normal half 100 FDDI 4/1 inactive 2 normal half 10 10BaseT 4/2 inactive 2 normal half 10 10BaseT 4/3 inactive 2 normal half 10 10BaseT 4/4 notconnect 1 normal half 10 10BaseT 4/5 inactive 2 normal half 10 10BaseT 4/6 此时, VLAN 2 和VLAN 20 还未激活.所以在VLAN 2和VLAN 20的端口是inactive状态. 设置VLAN 20 如果在网络里有VTP server和VTP clent,请在VTP server上设置VLAN 20 Cat5001> (enable) set vlan 20 VLAN 20 modified 这将激活在所有管理域cisco内的VLAN 20 Cat5001> (enable) sho vlan 20 VLAN Name Status Mod/Ports ---- -------------------------------- --------- ---------------------------- 20 VLAN0020 active 1/1 5/1-6 VLAN Type SAID MTU Parent RingNo BridgeNo Stp Trans1 Trans2 ---- ----- ---------- ----- ------ ------ -------- ---- ------ ------ 20 enet 100020 1500 - - - - 0 0 配置Router conf t interface FastEthernet0/0.1 <-- you need to create a sub-interface by vlan. encapsulation isl 20 <-- 20 is the vlan number. ip address 1.1.1.1 255.255.255.0 interface FastEthernet0/0.2 encapsulation isl 2 ip address 2.2.2.1 255.255.255.0 interface FastEthernet0/0.3 encapsulation isl 1 ip address 172.16.80.1 255.255.255.0 Router eigrp 666 network 1.0.0.0 network 2.0.0.0 network 172.16.80.0 end writ mem |
凌众科技专业提供服务器租用、服务器托管、企业邮局、虚拟主机等服务，公司网站：http://www.lingzhong.cn 为了给广大客户了解更多的技术信息，本技术文章收集来源于网络,凌众科技尊重文章作者的版权，如果有涉及你的版权有必要删除你的文章，请和我们联系。以上信息与文章正文是不可分割的一部分,如果您要转载本文章,请保留以上信息，谢谢! |
